Parts & Accessories

The Sport Recreational Helmet Vent Light is one of the easiest and most powerful ways to increase visibility and safety on the road.

This helmet mount works with all CatEye Lights. Pair it with the Volt 800 for the ultimate trail solution.

Add the safety of visibility to your helmet and light up the trail, road, or commute with help from the Bontrager Helmet Mount. Easily attaches a light to most helmets. - Works with all Bontrager Ion and Flare lights

Replacement fit systems keep you comfy and secure Fit systems work hard to keep your helmets secure and to maximize safety. No matter what happens, these original replacements will get them working like new - Original equipment replacement Boa System for your Bontrager WaveCel helmet - Not compatible with non-WaveCel helmets - Full-length fit system designed for use with Medium and Large sized helmets - Short length fit system designed to optimize the fit of Small sized helmets

The ultimate commuter helmet cover combrines a fully reflective fabric, with water and wind protection. - Sugoi's fully reflective and waterproof Zap fabric is designed for high visibility in low light - Two sizes to offer a wider range of fit possibilities

For Serfas Metro Helmet – Replacement Rear Light Serfas Metro Helmet Compatibility: - HT-404BKGY - HT-400BKGY - HT-404BLBK - HT-400BLBK - HT-404WTBK - HT-400WTBK

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. Sizing: - Small = 52 – 56cm - Medium = 55 – 59cm - Large = 58 – 61cm

Replacement Pads for Lazer's BOB Helmet

- Replacement Pads for Lazer's Blade, Magma, Elle, or Jade helmets - X-Static pads are an anti-microbial, self-cleaning pad system

- Replacement X-Static pads for Lazer's Wasp Air Helmet - X-Static pads are an anti-microbial, self-cleaning pad system

You need to get out on your bike even in terrible weather. Fitting in an early commute or a mid-winter ride is easier when you're warm, comfortable, and visible. Keeping your head warm in bad weather can be the best way to fend off the elements. - GORE-TEX Product: durably waterproof, windproof and extremely breathable - Reflective band - Elastic hem - Reflective logo - Durably waterproof - Extremely breathable - All weather conditions - Engineered for Cycling - Weight: 0.8 ounces

Let's face it - we all sweat. Sweat stinks. Fresh pads will make your helmet smell and fit just like it did when it was new. Key features - Original equipment replacement fit pads for your Bontrager Ballista MIPS helmet - Also compatible with non-MIPS Bontrager Ballista helmet - Helmet fit pads should be replaced once per year to maintain fit and hygiene

These covers are key to keeping your Ballista helmet aero and cool. No matter what happens, these original replacements will get them working and looking like new. - Works perfectly with your Bontrager Ballista helmet - Original equipment replacement vent covers

New pads help your helmet fit best and smell fresh Let's face it—we all sweat. Sweat stinks. Fresh pads will make your helmet smell, and fit, just like it did when it was new. - Original equipment replacement fit pads for your Bontrager Blaze WaveCel helmet - Helmet fit pads should be replaced once a year to maintain fit and hygiene

Replacement visors keep your lids fresh Helmet visors work hard to get the sun out of your eyes and keep you looking good. No matter what happens, these original replacements will get them working like new. - Works perfectly with your Bontrager Blaze WaveCel helmet - Original equipment replacement visor

New pads help your helmet fit best and smell fresh Let's face it—we all sweat. Sweat stinks. Fresh pads will make your helmet smell, and fit, just like it did when it was new. - Original equipment replacement fit pads for your Bontrager Blaze WaveCel helmet - NoSweat keeps sweat out of eyes through channeled pads for constant clarity - Helmet fit pads should be replaced once a year to maintain fit and hygiene

Where your gaze goes, your light follows Add the safety of visibility to your helmet and light up the trail with help from the Bontrager Blaze helmet mount. Compatible with all Ion headlights. - Quickly mount front light and camera accessories on the front of your Bontrager Blaze WaveCel helmet - Tested with an accelerometer for intended breakaway point if involved in a crash

Easily integrated Designed specifically for specific Bontrager Circuit MIPS road bike helmets, the Blendr mount easily integrates Bontrager Ion lights and GoPro cameras. - Quickly mount front light and camera accessories on the front of your Bontrager Circuit MIPS road bike helmet. - Tested with an accelerometer for intended breakaway point if involved in a crash

Easily integrated Designed specifically for specific Bontrager Circuit MIPS road bike helmets, the Blendr mount easily integrates Bontrager Ion lights and GoPro cameras. - Quickly mount rear light to the back of your Bontrager Circuit MIPS road bike helmet - Tested with an accelerometer for intended breakaway point if involved in a crash

New pads help your helmet fit best and smell fresh Let's face it - we all sweat. Sweat stinks. Fresh pads will make your helmet smell, and fit, just like it did when it was new. - Original equipment replacement fit pads for your Bontrager Charge WaveCel helmet - Helmet fit pads should be replaced once a year to maintain fit and hygiene

New pads can help you dial in your perfect fit - keeping you comfortable and looking forward to the next ride. New pads help your helmet fit best and smell fresh Let's face it - we all sweat. Sweat stinks. Fresh pads will make your helmet smell and fit just like it did when it was new. Key features - Original equipment replacement fit pads for your Bontrager Circuit MIPS helmet - Also compatible with non-MIPS Bontrager Circuit helmet - Helmet fit pads should be replaced once per year to maintain fit and hygiene

Let's face it - we all sweat. Sweat stinks. Fresh pads will make your helmet smell, and fit, just like it did when it was new. New pads can also help you dial in your perfect fit - keeping you comfortable and looking forward to the next ride. - Original equipment replacement fit pads for your Bontrager Dipper helmet - Helmet fit pads should be replaced once a year to maintain fit and hygiene

Let's face it - we all sweat. Sweat stinks. Fresh pads will make your helmet smell and fit just like it did when it was new. Key features - Original equipment replacement fit pads for Bontrager Dipper MIPS helmets - Not compatible with non-MIPS Bontrager Dipper helmets - Helmet fit pads should be replaced once per year to maintain fit and hygiene

Helmet buckles work hard to keep your helmets secure and to maximize safety. No matter what happens, these original replacements will get them working like new. Key features - Original replacement buckles for your Bontrager helmet - Compatible with all Bontrager helmets

The key to getting your helmet fit pads stay put Bontrager helmet fit pads are affixed to the inside of the helmet via this Velcro kit. No matter what happens, these original replacements will get them sticking like new. Product details - Replacement adhesive Velcro kit - Compatible with all Bontrager helmets

New pads help your helmet fit best and smell fresh Let's face it—we all sweat. Sweat stinks. Fresh pads will make your helmet smell, and fit, just like it did when it was new. - Original equipment replacement fit pads for your Bontrager Starvos MIPS helmet - Also compatible with non-MIPS Bontrager Starvos helmet - Helmet fit pads should be replaced once a year to maintain fit and hygiene

Key features - Original equipment replacement Boa System for your Bontrager helmet - Compatible with all Boa-equipped Bontrager helmets, except Velocis MIPS - Can also be used to upgrade your Headmaster-equipped Bontrager helmet to the Boa System

Fit systems work hard to keep your helmets secure and to maximize safety. No matter what happens, these original replacements will get them working like new. - Original replacement fit systems for your Bontrager helmet - Compatible with all Bontrager helmets with Headmaster I or II fit systems

Bontrager's LockDown strap dividers are essential for a great fitting, secure helmet. No matter what happens, these original replacements will get them working like new. Key features: - Original replacement strap dividers for your Bontrager helmet - Compatible with all Bontrager helmets equipped with LockDown Straps

Product Details - Original equipment replacement fit pads for Bontrager Lithos helmet - Helmet fit pads should be replaced once per year to maintain fit and hygiene